Table of contents
- Intro
- Enraged Rabbit Carrot Feeder
- Sourcing Parts
- Printing Parts
- Enraged Rabbit Carrot Patch
- Sourcing Parts
- Printing Parts
- Mods
- Printable Chain
- Easy BRD
Intro
I purchased an already built, 9 channel Enraged Rabbit Carrot Feeder from the Voron Discord garage sale. I plan on dismantling it to use the parts for V2.0 and using the printed parts to build a 6 channel to use on the AM8 when it is built.
Enraged Rabbit Carrot Feeder
Sourcing Parts
Electronics
| Item | Quantity | Received | Notes |
|---|
| ERCF EASY BRD | 1 | 1 | |
| NEMA14 Motor 14HS11-1004S | 1 | 1 | Oukeda Motor OK35STH34-1254A |
| NEMA17 Motor 17HS08-1004S | 1 | 1 | Oukeda Motor OK42STH20-104A-XH400 |
| TowerPro MG90S servo | 1 | 1 | |
| TMC2209 Stepper drivers | 2 | 2 | |
| TCRT5000 sensor pcb | 1 | 1 | |
| Omron Mouse Button - Micro Switch | 1 | 1 | |
Hardware
| Item | Quantity | Received | Notes |
|---|
| 7 sets of bondtechs gears | 7 | 7 | |
| LM8UU bearings | 2 | 2 | |
| M5 threaded rods | 2 | 2 | 156mm for 6 channel |
| 8mm smooth rods | 2 | 2 | 171mm for 6 channel |
| D-cut 5mm shaft | 1 | 1 | 201mm for 6 channel |
| MR623ZZ bearing | 1 | 1 | |
| MR85ZZ bearings | 6 | 6 | |
Fasteners
| Item | Quantity | Received | Notes |
|---|
| M3 threaded inserts | 28 | 32 | |
| M5x30 BHCS | 2 | 2 | |
| M5x16 BHCS | 1 | 1 | |
| M5 nuts | 4 | 5 | |
| M5 nylock nuts | 5 | 6 | |
| M5 washers | 2 | 3 | |
| M3x8 SHCS | 22 | 22 | |
| M3x8 BHCS | 5 | 5 | |
| M3x12 SHCS | 3 | 3 | |
| M3x16 SHCS | 10 | 13 | |
| M3x20 SHCS | 7 | 7 | |
| M3x40 SHCS | 2 | 2 | |
| M3 DIN125 Steel Washer | 9 | 13 | |
| M2x10 SHCS | 2 | 2 | |
Motion
| Item | Quantity | Received | Notes |
|---|
| GT2 belt 6mm (open) | 1 | 1 | 412mm for 6 channel |
| GT2 20T Pulley 6 mm, 5mm bore | 3 | 3 | |
| GT2 20T Toothed Idler 6 mm, 5mm bore | 1 | 1 | |
| GT2 188m Belt loop 6mm | 1 | 1 | |
Misc
| Item | Quantity | Received | Notes |
|---|
| 6mm x 3mm Round Neodymium Magnets | 22 | 23 | |
| Bowden Clip | 7 | 10 | |
| Bowden Fitting | 7 | 10 | |
| 7X7 Drag chain | 1 | 1 | |
| Item | Quantity | Received | Notes |
|---|
| AH3364Q-P-B Hall Effect sensor (SIP) | 1 | 2 | |
| M3 DIN125 Steel Washer | 1 | 2 | |
| 6mm x 3mm Round Neodymium Magnets | 1 | 2 | |
| M3x8 SHCS | 1 | 2 | |
| M3x12 SHCS | 1 | 2 | |
| JST XH 3 pins male connector | 1 | 2 | |
Printing Parts
Filament Blocks
Magnetic Gates
Tag Plates
| Item | Quantity | Material | Printed | Notes |
|---|
| Tag_Plate_0 | 1 | Blue ABS | ✔️ | Will reprint the Multi colour version when the ERCF is installed and tuned |
| Tag_Plate_1 | 1 | Blue ABS | ✔️ | Will reprint the Multi colour version when the ERCF is installed and tuned |
| Tag_Plate_2 | 1 | Blue ABS | ✔️ | Will reprint the Multi colour version when the ERCF is installed and tuned |
| Tag_Plate_3 | 1 | Blue ABS | ✔️ | Will reprint the Multi colour version when the ERCF is installed and tuned |
| Tag_Plate_4 | 1 | Blue ABS | ✔️ | Will reprint the Multi colour version when the ERCF is installed and tuned |
| Tag_Plate_5 | 1 | Blue ABS | ✔️ | Will reprint the Multi colour version when the ERCF is installed and tuned |
Tag Plates
| Item | Quantity | Material | Printed | Notes |
|---|
| Top_Hat_Locker_1 | 6 | Black ABS | ✔️ | Manual says to start with all tools at 1 |
Gearbox
Linear Axis
Selector
Supports
Enraged Rabbit Carrot Patch
Sourcing Parts
The Enraged Rabbit Carrot Patch manages filament reels being used by the Enraged Rabbit Carrot Feeder. Quantities are for 1 Patch. I should have enough parts for 2 patches.
Fasteners
| Item | Quantity | Received | Notes |
|---|
| M3 threaded inserts | 4 | 8 | |
| M3x8 SHCS | 2 | 4 | |
| M3x16 SHCS | 1 | 2 | |
| M3x20 SHCS | 1 | 2 | |
| M5 nylock nuts | 1 | 2 | |
| M5x30 BHCS | 1 | 2 | |
Misc
| Item | Quantity | Received | Notes |
|---|
| Bowden Clip | 2 | 4 | |
| Bowden Fitting | 2 | 4 | |
| PTFE Tube (4mm OD 3mm ID) - 30cm | 1 | 6m | |
Motion
| Item | Quantity | Received | Notes |
|---|
| 608ZZ Bearing | 1 | 2 | |
Printing Parts
Frame
Buffer Assembly
Sliding Arm
Mods
Printable Chain
The chain is smaller on the ERCF than the chain for the Voron build. I am not expecting to have any chain left over (especially as I am going to print Z chain) and rather than buying some more chain I will try printing it instead.
Printable Chain
Easy BRD
My SKR 1.4 Turbo does not have enough Stepper Motor Drivers to run the ERCF, this is a board specifically designed to run the Carrot Feeder.
Easy BRD
